Height-adjustable connections between load-bearing tower and superstructure.

Art.-No. 324

Height-adjustable, anti-tip connection between load-bearing tower and superstructure with one or two formwork secondary beams H20.

Art.-No. 325

Art.-No. 326

Connecting Scaffold tubes 48.3mm at any angle to the vertical tubes of load-bearing tower frames.

Art.-No. 341

For securing plates and accessory parts, for example to multi-purpose walings.

Art.-No. 344

Bearing plate for connectors with form-tie angles up to 15 °.

Art.-No. 349

Art.-No. 338191500

The Wall tie is designed to attach to a Scaffold tube and butt to a supporting structure. It is available in 1.00m and 1.50m.

Art.-No. 338191000

The Wall tie is designed to attach to a Scaffold tube and butt to a supporting structure. It is available in 1.00m and 1.50m.

Art.-No. 328460600

The U head is designed to be installed at the top of a scaffold. Particularly for Shoring applications where beams are required to be supported. Alternatively the U head can be used at the base of the scaffold by turning it upside down.

Art.-No. 328450600

The 4 way screw jack is designed to be installed at the top of a scaffold. Particularly for shoring applications where one more beams are required to be supported.

Art.-No. 319022575

The Alum ladder hatch deck 257cm acts as a lightweight, extra wide scaffold acess deck which incorporates a Ladder. It is available only with 2.57m.

Art.-No. 316052575

The inner guardrail extended is used to shield the inner side of a staircase tower at the exit providing a guardrail at landing bay. Available for stair lengths of 2.57m and 3.07m.

Art.-No. 306030780

The Swivel base jack is used as a starting base for a scaffold. It is adjustable in height and angle to allow for compensation on uneven surfaces so that a level scaffold is always attainable.

Art.-No. 306010600

The base jack is used to adjust the height of the scaffold. For base jack 60cm height adjustability is 40 – 450 mm.

Art.-No. 301793000

Standards hanging without spigot are used as “verticals” to transmit loads to the ground. The fact that they don´t have spigots, allows them to be used for shoring applications. Standards are available in incremintle lengths. Rosettes are welded every 50cm which allow to create a connection between different elements. In order to join 2 standards a Spigot needs to used. These standards are to be used for suspended Scaffolds

Art.-No. 301792000

Standards hanging without spigot are used as “verticals” to transmit loads to the ground. The fact that they don´t have spigots, allows them to be used for shoring applications. Standards are available in incremintle lengths. Rosettes are welded every 50cm which allow to create a connection between different elements. In order to join 2 standards a Spigot needs to used. These standards are to be used for suspended Scaffolds

Art.-No. 301791500

Standards hanging without spigot are used as “verticals” to transmit loads to the ground. The fact that they don´t have spigots, allows them to be used for shoring applications. Standards are available in incremintle lengths. Rosettes are welded every 50cm which allow to create a connection between different elements. In order to join 2 standards a Spigot needs to used. These standards are to be used for suspended Scaffolds

Art.-No. 301791000

Standards hanging without spigot are used as “verticals” to transmit loads to the ground. The fact that they don´t have spigots, allows them to be used for shoring applications. Standards are available in incremintle lengths. Rosettes are welded every 50cm which allow to create a connection between different elements. In order to join 2 standards a Spigot needs to used. These standards are to be used for suspended Scaffolds

Art.-No. 301790500

Standards hanging without spigot are used as “verticals” to transmit loads to the ground. The fact that they don´t have spigots, allows them to be used for shoring applications. Standards are available in incremintle lengths. Rosettes are welded every 50cm which allow to create a connection between different elements. In order to join 2 standards a Spigot needs to used. These standards are to be used for suspended Scaffolds

Art.-No. 301166145

Lattice girders are used to bear heavy loads at large spans or to create a bridging construction within the scaffold. Lattice girders are available in 5.14m, 6.14m, 7.71m. They are 50cm in depth and equipped with Terminal Wedges to connect to the rosettes on the standards. They come without spigot, but a separate spigot can be used.