Expendable form-tie component for single-sided tying.

Art.-No. 116

Art.-No. 588651000

Telescopic tool for operating the Framax lifting hook from ground level.

Art.-No. 068968

Art.-No. 069423

Hand scraper for removing concrete from formwork elements.

Art.-No. 069431

Cost-effective and lightweight, the Doka beam H20 basic P is a solid-web beam with its low weight and proven end reinforcement in the form of bevelled beam ends. (EN 13377-compliant).

Art.-No. 162

Plywood sheet made of Nordic birch with 120 g/m² phenolic-resin film coating on both sides. The glue-bonding meets the requirements of EN 314-2 Service Class 3 or BS 6566 WBP. The edges are sealed with acrylic-resin varnish.

Art.-No. 229

Triangular ledge with soft plastic lips for close fit to the surface of the panel. Used for making no-nails outside corners and column formwork with universal panels.

Art.-No. 260

Triangular ledge with soft plastic lips for close fit to the surface of the panel. Used for making no-nails outside corners and column formwork with universal panels.

Art.-No. 278

Art.-No. 306010600

The base jack is used to adjust the height of the scaffold. For base jack 60cm height adjustability is 40 – 450 mm.

Art.-No. 316080005

The inner guardrail is used to shield the inner side of a staircase tower. The inner guardrail suits for both stair lengths of 2.57m, 3.07m.

Art.-No. 586646000

Storage and transport device for Protective barriers Z.

The outer guardrail is used to shield the outer side of the staircase tower. Outer guardrails are available for stair lengths of 2.57m, 3.07m. The outer guardrail has a Swivel Wedge Terminal that allows to fix it to the rosette.

Art.-No. 455

Release agent specially for smooth formwork surfaces.

Art.-No. 496

Release agent specially for absorbent formwork surfaces.

Art.-No. 521

Ledgers are used as horizontals to connect standards and to transfer loads from platforms into standards. Ledgers are also used for making side protection of the scaffold. Ledgers are available in lengths 0.15m, 0.39m, 0.73m, 1.04m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 549

Steel plans are used to create a working platform in a scaffold. They are placed directly onto the ledgers and secured with the integrated lift-out guard. Steel planks are available with two widths 0.19m and 0.32m and in lengths 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 557

Steel planksare used to create a working platform in a scaffold. They are placed directly onto the ledgers and secured with the integrated lift-out guard. Steel planks are available with two widths 0.19m and 0.32m and in lengths 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 559

Steel toe boards are mounted on working platforms to prevent material from falling down. These Toeboards are galvanized and not yellow.

Art.-No. 561

Bay braces are essential to increase the vertical stiffness of the scaffold! For stabilizing the outer plane of the scaffold, parallel and perpendicular to the facade, vertical braces are used. Vertical braces are placed in at least every 5th bay on every lift and in every end bay perpendicular to the facade. Diagonals are available for 1.00m, 1.50m and 2.0m heights, and bay lengths of 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 574