Art.-No. 335150024

A spring pin EU is used to connect two standards together and must be used during crane lifting. It can be substituted with an M12x60 8.8 hexagonal bolt and nut.

The bracket is used to create an extended platform outside the scaffold and to add a "cantilever" to the construction. Brackets are available in lengths 0.39m, 0.73m and 1.09m.

Art.-No. 543

Ledgers are used as horizontals to connect standards and to transfer loads from platforms into standards. Ledgers are also used for making side protection of the scaffold. Ledgers are available in lengths 0.15m, 0.39m, 0.73m, 1.04m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 549

Steel planksare used to create a working platform in a scaffold. They are placed directly onto the ledgers and secured with the integrated lift-out guard. Steel planks are available with two widths 0.19m and 0.32m and in lengths 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 559

Art.-No. 682004000

For connecting two Scaffold tubes 48.3mm at an angle of 90°.

The Toe board retaining clamps are used to secure the toeboard from uplift in adverse weather conditions.

Art.-No. 476

The wall tie tube is a scaffold tube with pin, designed to keep the standards in the vertical position without buckling.

Art.-No. 689

The stairs are used to provide access to the various deck levels within the scaffold. The aluminum platform stairs are suitable for 2.00 kN/m² (EN12811: class 3). Alu-stairways are available in lengths of 2.57m, 3.07m.

Art.-No. 718

Mid Transom can create a transom at the lift anywhere inside the bay when installed onto a Ledger and can also create openings within the planked bay for Ladder access or to avoid a permanent obstruction.

Art.-No. 729

Standards with presseded spigot are used as “verticals” to transmit loads to the ground. Rosettes are welded every 50cm which allow to create a connection between different elements. These standards are not to be used for suspended scaffolds! Standards are available in incremintle lengths from 0.50m to 4.00m.

Art.-No. 844

Lattice girders are used to bear heavy loads at large spans or to create a bridging construction within the scaffold. Lattice girders are available in 5.14m, 6.14m, 7.71m. They are 50cm in depth and equipped with Terminal Wedges to connect to the rosettes on the standards. They come without spigot, but a separate spigot can be used.

Art.-No. 723

Standards hanging without spigot are used as “verticals” to transmit loads to the ground. The fact that they don´t have spigots, allows them to be used for shoring applications. Standards are available in incremintle lengths. Rosettes are welded every 50cm which allow to create a connection between different elements. In order to join 2 standards a Spigot needs to used. These standards are to be used for suspended Scaffolds

Art.-No. 845

Art.-No. 310012004

Adjustable swing gate designed to secure an opening used for access & egress. It allows to cover openings from 0.88 m to 1.35 m.

Art.-No. 306110004

The base jack retention prevents the kicker lift to fall off when hoisting the scaffold. It has a terminal wedge and a half coupler allowing to high versatility of the component.

Art.-No. 301300014

Rosette clamp horizontal allows a Ledger to be connected anywhere along the length of a bay. Allowing to create an intermediate transom.

Art.-No. 301300004

The Rosette clamp allows to add an additional rosette to any point along the vertical (tube Standard). It can accomodate up to six connection points.

Art.-No. 305032004

The Spigot adapter with clamp-bolt is used for creating handrails smaller than the bay length.

Art.-No. 316070010

The Aluminium Stair Guardrails are used to provide handrails on the inner side and outer side of the Aluminium Stair Platforms.