Art.-No. 301011500

Standards with crimped spigots are used as uprights to transmit loads to the ground. Rosettes are welded on every 50cm for interconnecting elements. Do not use these standards for suspended scaffolds! Standards are available in incremental lengths from 0.50m to 4.00m.

Art.-No. 301010500

Standards with crimped spigots are used as uprights to transmit loads to the ground. Rosettes are welded on every 50cm for interconnecting elements. Do not use these standards for suspended scaffolds! Standards are available in incremental lengths from 0.50m to 4.00m.

Art.-No. 301270000

Starter base collars, each with a single rosette placed on the base jack, form a ready-to-use base for the rest of the scaffold. The base collar facilitates alignment of a modular structure.

Art.-No. 301280000

Leg locks, used in pairs, attach to the bottom rosette of the top standard and to the top rosette of the bottom standard. They lock the standards together in preparation for suspended or lifted scaffold applications.

Art.-No. 335040000

Spigots for hanging scaffolds are necessary for connecting standards without spigots in suspended scaffolds (2 bolt axes per connection).

Art.-No. 307070100

Castor wheels provide mobility, enabling a medium to large scaffold tower to be wheeled across a flat surface.

Gap filler planks span small openings in Ringlock platforms or between bays. They can be overlapped on circular scaffolds to close the corner gaps. They come complete with plastic plugs for fitting. They are available in two widths: 0.32m and 0.19m and in three lengths: 1.00m, 1.50m and 2.00m.

Art.-No. 468

Prevents adhesion between concrete and cone with insulation up to 11 cm thick.

Art.-No. 486

Release agent specially for smooth formwork surfaces.

Art.-No. 496

Release agent specially for absorbent formwork surfaces.

Art.-No. 521

Truss ledgers have the same function as normal ledgers: They are used as horizontals to interconnect standards, to transfer loads from platforms into standards and to construct side protection for the scaffold. Their reinforced design enables them to transfer higher loads than normal ledgers. Double ledgers are available in lengths of 1.40m, 1.57m, 2.07m, 2.57m and 3.07m.

Art.-No. 527

Side brackets are used to construct an extended platform outside the scaffold and to add a cantilever to the construction. Side brackets are available in lengths of 0.39m, 0.73m and 1.09m.

Art.-No. 543

Ledgers are used as horizontals to interconnect standards and to transfer loads from platforms to the standards. Ledgers are also used to construct side protection for the scaffold. Ledgers are available in lengths of 0.15m, 0.39m, 0.73m, 1.04m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m and 3.07m.

Art.-No. 549

Infill planks with 19cm are designed to fill any unwanted gaps between planks or bays providing a continuous working platform. They are available in the sizes of the most common bays: 0.65m, 0,88m, 1.065m, 1.57m, 2.13m, 2.43m, 3.05m.

Art.-No. 556

Steel planks are used to construct a working platform in a scaffold. They are laid directly on the ledgers and secured with the integral lift-out guard. Steel planks are available in two widths of 0.19m and 0.32m and in lengths of 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m and 3.07m.

Art.-No. 557

Steel planks are used to construct a working platform in a scaffold. They are laid directly on the ledgers and secured with the integral lift-out guard. Steel planks are available in two widths of 0.19m and 0.32m and in lengths of 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m and 3.07m.

Art.-No. 559

Steel toeboards are mounted on working platforms to prevent material from dropping off. These toeboards are galvanized and do not have a yellow finish.

Art.-No. 561

Bay braces are essential for increasing the vertical stiffness of the scaffold! Vertical braces are used parallel and perpendicular to the facade for stabilizing the outer plane of the scaffold. Vertical braces are installed in at least every 5th bay on every lift and in every end bay perpendicular to the facade. Diagonals are available for heights of 1.00m, 1.50m and 2.0m and for bay lengths of 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m and 3.07m.

Art.-No. 574

Art.-No. 743500001

For turning and holding the tie rods.

Art.-No. 202