Bay braces are essential to increase the vertical stiffness of the scaffold! For stabilizing the outer plane of the scaffold, parallel and perpendicular to the facade, vertical braces are used. Vertical braces are placed in at least every 5th bay on every lift and in every end bay perpendicular to the facade. Diagonals are available for 1.00m, 1.50m and 2.0m heights, and bay lengths of 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Toote nr 574

Allows advancing guard rail protection during erection, modification and dismantling of the scaffold.

Toote nr 636

The wall tie tube is a scaffold tube with pin, designed to keep the standards in the vertical position without buckling.

Toote nr 689

The Gap Filler Plates are designed to fill any unwanted gaps between planks or bays creating continuous platforms and can easily be installed in the same method as the infill planks and can be secured to the main planks.

Toote nr 690

The Plan Braces are used for lateral bracing between the node points on the Ringlock Standards. The Plan Braces come in various sizes to suit the bay range.

Toote nr 691

The Plan Braces are used for lateral bracing between the node points on the Ringlock Standards. The Plan Braces come in various sizes to suit the bay range.

Toote nr 692

The stairs are used to provide access to the various deck levels within the scaffold. The aluminum platform stairs are suitable for 2.00 kN/m² (EN12811: class 3). Alu-stairways are available in lengths of 2.57m, 3.07m.

Toote nr 718

The inner guardrail 1m is used to shield the inner side of a 1m staircase.

Toote nr 719

The Girder transom enables a standard to be installed along the length of a bay when secured to two standards.

Toote nr 730

Plank to plank transoms can be placed between two decks within a bay to support decks e.g. for making ladder openings or create openings. They are available in widths equivalent to 1, 2 and 3 Boards.

Toote nr 815

Standards with presseded spigot are used as “verticals” to transmit loads to the ground. Rosettes are welded every 50cm which allow to create a connection between different elements. These standards are not to be used for suspended scaffolds! Standards are available in incremintle lengths from 0.50m to 4.00m.

Toote nr 844

Toote nr 319023075

The Ladder Hatch Plank acts as a lightweight, extra wide Scaffold Plank which incorporates a hatch and a ladder.

Toote nr 310067004

The Access barriers are designed to be used as a guardrail at the top and bottom of the Aluminum 4 leg Platform Stairs and can also be used to provide barriers around gaps in platforms for ladder access.

Toote nr 335150025

Spring pin for securing standard-to-standard connections.

Toote nr 333040005

The Ballast weight holder secures to the Standard to prevent overturning when used with Ballast weights.

Toote nr 333040015

The Ballast weight is installed onto the Ballast weight holder.

Toote nr 301880735

Allows advancing guard rail protection during erection, modification and dismantling of the scaffold.

Toote nr 301881095

Allows advancing guard rail protection during erection, modification and dismantling of the scaffold.

The Ladder Hatch Plank acts as a lightweight, extra wide Scaffold Plank which incorporates a hatch.

Toote nr 722

Lattice girders are used to bear heavy loads at large spans or to create a bridging construction within the scaffold. Lattice girders are available in 5.14m, 6.14m, 7.71m. They are 50cm in depth and equipped with Terminal Wedges to connect to the rosettes on the standards. They come without spigot, but a separate spigot can be used.

Toote nr 723